Reduce Install time / Improve Performance and Reliability PLUS One Stop Fault and Warranty Support from the Team at Enerdrive
Enerdrive have spent considerable time developing a simple, turn-key installation plate for the Caravan, Motorhome, Camper Trailer and Commercial vehicle markets. Over the years, it’s evident that most product issues occur when simple mistakes are made at the time of installation so we set out to find a way to improve installation time and reliability.
The Right Products for the Right Solution
Our Enerdrive Installation Plates have been designed with the right mix of products that you need, without going over the top to keep costs at a minimum. We believe that these product mixes and layouts work, However if you have an ongoing application, we can also custom configure a specific layout to suit your needs. All systems come complete with a full wiring diagram and user manuals can be put together in your own format should you require for your user manuals.
One Stop Tech and Warranty Spot
By using the Enerdrive Installation Plates, any fault or product issue can be easily identified in consultation with the owner and the tech team at Enerdrive. Our plates are designed for ease of replacement of all components with threaded mounting brackets and cable connections and if needed could be done by the actual owner with the support of the Enerdrive team via phone.
This approach has been very successful of late with our end user Tech Support phone calls, when we know a specific van/customers exact installation and setup.
One Brand – One Company – One Solution – Why wouldn’t you choose and Enerdrive Installation Plate?
AGM INSTALLATION PLATES
All components are Pre-Installed on white Powder coated—besides battery monitor cable as this needs to be run to monitor mounting location.
20A AGM Installation Plate
(600mm x 410mm)
Part#: K-AGM-BOARD-1
40A AGM Installation Plate
(600mm x 410mm)
Part#: K-AGM-BOARD-2
eLite Battery Monitor included with AGM Installation Kits.
20A & 40A Installation Plates includes the following:
- 1 x Mounting Plate
- 1 x eLITE Battery Monitor with Shunt
- 7m x 8core Twisted Pair battery monitor Cable
- ePOWER 20A or 40A AC Charger
- ePOWER DC2DC 30A with MPPT Solar Input
- 1 x Blue Sea Safety Hub 150 fuse distribution block
- 2 x MIDI Fuses Positions for Chargers
- 2 x MIDI Fuses Positions for Loads (1 pre-connected to LBCO Circuit)
- 6 x ATO/ATC Fuse Positions for 24hr loads
- Negative Bus bar
- 1 x Low battery disconnect for Non essential loads
- Slotted Ducting to neatly run the cables
LITHIUM INSTALLATION PLATES
All components are Pre-Installed on white Powder coated—besides battery monitor cable as this needs to be run to monitor mounting location.
40A Lithium Installation Plate
(745mm x 410mm)
Part#: K-LITH-BOARD-1
60A Lithium Installation Plate
(745mm x 410mm)
Part#: K-LITH-BOARD-3
ePro Battery Monitor included with Lithium Installation Kits.
40A & 60A Lithium Installation Plates includes the following:
- 1 x Mounting Plate
- 1 x ePRO Battery Monitor with Shunt
- 7m x 8core Twisted Pair battery monitor Cable
- ePOWER 40A or 60A AC Charger
- ePOWER DC2DC 30A with MPPT Solar Input
- Negative Bus bar
- Enerdrive Advanced BMS Relay Driver
- 500A Latching Relay
- 2 x MIDI Fuse & Holders for Chargers
- 2 x MIDI Fuses & Holders for Load Circuits
- 1 x ANL Fuse Holder for Inverter
- Slotted Ducting to neatly run the cables
- 2 x 1.5m of 95mm DC Battery cable.
Lithium Installation Plate 1600 Combi
(745mm x 410mm)
Part#: K-LITH-BOARD-2
ePro Battery Monitor included with Lithium Installation Kits.
ePRO Combi Lithium Installation Plates includes the following:
- 1 x Mounting Plate
- 1 x ePRO Battery Monitor with Shunt
- 7m x 8core Twisted Pair battery monitor Cable
- ePRO Combi 1600va Inverter with 60Amp charger
- ePOWER DC2DC 30A with MPPT Solar Input
- Morningstar TriStar 45A solar Controller
- Negative Bus bar
- Enerdrive Advanced BMS Relay Driver
- 500A Latching Relay
- 2 x MIDI Fuse & Holders for Chargers
- 1 x MIDI Fuses & Holders for Load Circuits
- Slotted Ducting to neatly run the cables
- 2 x 1.5m of 95mm DC Battery cable.